YY026MG Yemagetsi Tensile Simba Tester
Ichi chiridzwa iindasitiri yemachira yemba ine simba bvunzo kumisikidzwa kweyepamusoro-giredhi, yakakwana basa, yakanyanya kunaka, yakagadzikana uye yakavimbika maitiro emhando.Inoshandiswa zvakanyanya mushinda, machira, kudhinda uye dhayi, machira, zvipfeko, zipper, dehwe, nonwoven, geotextile uye mamwe maindasitiri ekupwanya, kubvarura, kutyora, kupemha, musono, elasticity, creep test.
GB/T, FZ/T, ISO, ASTM
1. Adopt kunze kwenyika servo mutyairi uye mota (vector control), iyo mota yekupindura nguva ipfupi, hapana kukurumidza kumhanyisa, kumhanya kusaenzana chiitiko.
2. Yakasarudzwa bhora sikuruu uye yakananga gwara renjanji inogadzirwa neGermany Rexroth Company, ine hupenyu hurefu hwebasa, ruzha rwakaderera uye kuderera kwakadzika.
3. Yakashongedzerwa neiyo encoder yakaunzwa kuti inyatso kudzora kumira uye kurebesa kwechiridzwa.
4. Yakashongedzerwa nepamusoro-soro sensor, "STMicroelectronics" ST series 32-bit MCU, 24 A / D converter.
5. Yakashongedzerwa nepneumatic fixture, clip inogona kutsiviwa, uye inogona kugadzirwa nezvinhu zvevatengi.
6.Can kugadzirwa maererano nezvinodiwa nevatengi.
7. Online software inotsigira Windows operating system,
8. Chimbo chinotsigira mugadziri uye komputa nzira mbiri.
9.Pre tension software digital setting.
10. Kureba kwema digital setting, automatic positioning.
11. Kudzivirirwa kwakajairika: mechanical switch protection, yepamusoro uye yakaderera muganhu wekufamba, overload protection, over-voltage, over-current, overheating, under-voltage, under-current, leakage automatic protection, emergency switch manual protection.
12. Kubvarura, peel test curve peak kusarudzwa uye kutsunga mamiriro anogona kuiswa nemutengi.
13. Simbisa kukosha kwekuenzanisa: dhijitari kodhi calibration (kubvumidza kodhi), zviri nyore kusimbiswa kwechiridzwa, kutonga chaiko.
14. Yese muchina wedunhu standard modular dhizaini, yakanakira chiridzwa kugadzirisa uye kusimudzira.
1. Iyo software inotsigira Windows inoshanda system, kunze kwebhokisi, iri nyore kwazvo, pasina kudzidziswa kwehunyanzvi.
2. Ikombiyuta yepaIndaneti software inotsigira kushanda kweChinese neChirungu.
3. Simbisa chirongwa chekuedza chakasimbiswa nemushandisi, imwe neimwe parameter ine kukosha kwekusagadzikana, mushandisi anogona kugadzirisa.
4. Parameter setting interface: nhamba yezvinhu zvemuenzaniso, ruvara, batch, nhamba yemuenzaniso uye mamwe mapeji anozvimiririra akaiswa uye anodhindwa kana kuchengetwa.
5. Basa rekuswededza mukati nekunze kwenzvimbo dzakasarudzwa dzetest curve.Dzvanya chero poindi yetest point kuratidza iyo tensile uye elongation kukosha.
6. Mushumo wedata rebvunzo unogona kushandurwa kuita Excel, Shoko, nezvimwewo, otomatiki yekutarisisa mhinduro dzebvunzo, yakanakira kubatana nevatengi bhizinesi manejimendi software.
7.Chiedza chekuedza chinochengetwa kuPC, kuitira kuti inyore kubvunzurudza.
8. The test software inosanganisira dzakasiyana-siyana simba rekuedza nzira, kuitira kuti bvunzo zvive nyore, nekukurumidza, kwakaringana uye kudhura kwakaderera kushanda.
9. Chikamu chakasarudzwa checurve chinogona kuswededzwa mukati uye kunze pakuda panguva yekuedzwa.
10. Iyo yakaedzwa sample curve inogona kuratidzwa mumushumo wakafanana semhedzisiro yebvunzo.
11. Statistical point function, kureva kuverenga data pane yakayerwa curve, inogona kupa huwandu hwemapoka e20 data, uye kuwana inowirirana elongation kana simba resimba zvichienderana nekusiyana kwesimba kukosha kana elongation kupinza nevashandisi.
15. Multiple curve superposition basa.
16. Zviyero zvikamu zvinogona kushandurwa zvisina tsarukano, senge Newton, pondo, simba remakirogiramu uye zvichingodaro.
17. Software yekuongorora basa: kuputsa nzvimbo, kuputsa nzvimbo, pfungwa yekunetseka, goho poindi, yekutanga modulus, elastic deformation, plastiki deformation, nezvimwe.
18.Unique (host, komputa) nzira mbiri dzekudzora tekinoroji, kuitira kuti bvunzo zvive nyore uye nekukurumidza, mhinduro dzebvunzo dzakapfuma uye dzakasiyana-siyana (data report, curves, graphs, report).
1. Range uye indexing kukosha: 2500N, 0.05N;500 N, 0.005 N
2. Kugadziriswa kwesimba ndeye 1/300000
3. Simbisa kunyatsoita sensor: ≤± 0.05%F·S
4. Kurongeka kwemuchina: chiyero chakazara che2% ~ 100% chero nhanho chaiyo ≤± 0.1%, giredhi: 1 nhanho
5. The beam speed adjustment range (kumusoro, pasi, speed regulation, fixed speed) :(0.1 ~ 1000) mm/min (mukati mechikamu chekugadzika kwemahara)
6. Kubudirira sitiroko: 800mm
7. Displacement kugadziriswa: 0.01mm
8.The shoma clamping kureba: 10mm
9. Clamping distance positioning mode: digital setting, automatic positioning
10. Gantry upamhi: 360mm
11. Kushandurwa kweyuniti: N, CN, IB, IN
12. Kuchengetera data (host part) :≥2000 mapoka
13. Simba rekushandisa: 220V, 50HZ, 1000W
14. Kukura kwekunze: 800mm×600mm×2000mm (L×W×H)
15. Kurema: 220kg
1. Host---1 Pcs
2.Clamps:
1)Pneumatic Clamps-- 1 Set (kusanganisira clamping sheet:25×25,60×40,160×40mm)
2) Teerera neGB/T19976-2005 simbi bhora rinoputika simba basa pneumatic clamping clamps---1 Set
3.High quality yakanyarara pombi yemhepo--1 Set
4.On line analysis software---1 Set
5.On-line kutaurirana zvishandiso---1 Set
6.Kutakura Cell: 2500N / 500N
7.Software configuration: quality control operating software (CD) ---1 PCS
8.Tensile Clamps:
2N---1 Pcs
5N---1 Pcs
10N---1 Pcs
GB/T3923.1--- Micheka - Kutemerwa kwesimba rekusimba panguva yekuzorora uye kureba panguva yekuzorora - Strip nzira
GB/T3923.2--- Micheka -- Kutemerwa kwezvinhu zvinorema zvemachira -- Kutsunga kwekupwanya simba uye kureba panguva yekuzorora -- Kubata nzira
GB/T3917.2-2009---Kubvarura zvivakwa zvemachira - Kutsunga kubvarura simba rebhurukwa sampuli (musono mumwe chete)
GB/T3917.3-2009--- Zvipfeko - Kutsunga kwekubvarura simba reiyo trapezoidal specimens
GB/T3917.4-2009---- Zvipfeko - Kubvarura zvimiro zvemienzaniso yemitauro (kaviri musono) - Kutsunga kwekubvarura simba
GB/T3917.5-2009--- Micheka - Kubvarura zvimiro zvemachira - Kutsinhanisa kubvarura simba reiyo airfoil specimens (musono mumwe chete)
GB/T 32599-2016--- Nzira yekuedza yekudurura simba rezvigadzirwa zvemachira
FZ/T20019-2006---Edza nzira yekubvisa machira akarukwa
FZ/T70007---Mhosva yekuyedza ye underarm seam simba rejaketi akarukwa
GB/T13772.1-2008---Textile michina - Kutemerwa kwekupokana kweshinda kutsvedza pamajoini - Chikamu 1: nzira yekugara ichitsvedza.
GB/T13772.2-2008---Textile michina - Kutemerwa kweshinda kuramba kutsvedza pamajoini - Chikamu 1: Yakagadziriswa mitoro nzira
GB/T13773.1-2008--- Micheka - Yakabatana tensile zvimiro zvemachira uye zvigadzirwa zvawo - Chikamu 1: Kutemerwa kwesimba rekubatana ne strip methodGB/T13773.2-2008---Macheka - Joint tensile zvimiro zvemachira uye zvigadzirwa zvavo - Chikamu 1: Kutemerwa kwesimba rekubatana nenzira yekubata
GB/T19976-2005--Macheka - Kutsunga kwekuputika kwesimba - Bhora nzira
FZ/T70006-2004--------------------------------------------------------- Yakarukwa jira rakasimba kudzoreredza bvunzo nzira yemutoro wakamisikidzwa
FZ/T70006-2004--- Muedzo we elastic kudzoreredza mwero wemachira akarukwa neyakagadziriswa elongation nzira.
FZ/T70006-2004--- Kuzorora kwekushushikana mune tensile elastic kupora bvunzo yejira rakarukwa.
FZ/T70006-2004------------------------------------------------------------------ Yakarukwa jira re-lastic kupora bvunzo nzira ye
FZ/T80007.1-2006---Mhosva yekuyedza yeganda simba rembatya uchishandisa adhesive lining
FZ/T 60011-2016- --Kuedza nzira yesvuura simba remachira akaumbwa
FZ/T 01030-2016--- Machira akarukwa uye elastic akarukwa -- Kutsunga kwesimba rekubatana uye kuwedzera -- Yepamusoro-kutyora nzira
FZ/T01030-1993--- Zvipfeko - Kutsunga kwekuputika kwesimba - Bhora nzira
FZ/T 01031-2016--- Machira akarukwa uye akarukwa akarukwa -- Kutsunga kwesimba remubatanidzwa uye kurebesa -- Bata sampling nzira
FZ/T 01034-2008--- Zvipfeko - Nzira yekuyedza yekusimba elasticity yemachira akarukwa
TS EN ISO 13934-1: 2013 Machira - Tensile zvimiro zvemachira - Chikamu 1: Kutsunga kwekupwanya simba uye kurebesa (mitsetse nzira)
TS EN ISO 13934-2 Textiles - Tensile zvivakwa zvemachira - Chikamu 2: Kutsunga kwekupwanya simba uye kureba (nzira yekubata)
TS EN ISO 13935-1 Textiles - Tensile zvivakwa zvemachira uye zvigadzirwa zvawo - Chikamu 1: Simba pakupwanya majoini (mitsetse nzira)
TS EN ISO 13935-2 Machira - Tensile zvimiro zvemachira uye zvigadzirwa zvawo - Chikamu 2: Simba pakupwanya majoini (sampling nzira)
TS EN ISO 13936-1 Machira - Sarudzo yekutsvedza kuramba kweshinda pamachira mumachira akarukwa - Chikamu 1: Yakagadziriswa seam mazaru.
TS EN ISO 13936-2: 2004 Machira - Sarudzo yekutsvedza kuramba kweshinda pamishoni mumachira akarukwa.Chikamu 2: Fixed Load Method
ISO 13937-2: 2000 --- Textile zvinhu.Kubvarura zvinhu zvemicheka.Chikamu 2: Kutsunga kwekubvarura simba rematirauzi emuenzaniso (imwe nzira yemisodzi)
ISO 13937-3: 2000--- Zvigadzirwa zvemucheka.Kubvarura zvinhu zvemicheka.Chikamu 3: Kutsunga kwekubvarura simba remhando dzemhepo (nzira imwe yekubvarura)
ISO 13937-4: 2000 --- Textile zvinhu.Kubvarura zvinhu zvemicheka.Chikamu 4: Kutsunga kwekubvarura simba remhando dzemitauro (kaviri kubvarura nzira)
ASTM D5034 (2013).
ASTM D5035 (2015)---Edza nzira yekupwanya simba uye kureba kwemachira (strip nzira)
ASTM D2261---- Sarudzo yeKubvarura Simba (CRE) yeMucheka neRurimi Rumwe Nzira
ASTM D5587----Kubvarura simba rejira rakayerwa nenzira ye trapezoidal
ASTM D434--- Yakajairwa kuyerwa kwekupokana kune majoini slip
ASTM D1683-2007---Yakajairwa kuyerwa kwekupokana kune majoini slip
BS4952--- Elongation pasi pemutoro wakatarwa (bar pattern)
